|
View unanswered posts | View active topics
Author |
Message |
Roy
|
Post subject: Posted: Sat Jun 18, 2005 3:11 pm |
|
Joined: Sun May 27, 2001 2:52 pm Posts: 5556 Location: Mehlingen,Rhineland Pfalz, Deutschland
|
Martin I will be permently in Ktown in a bout a week in a half. I will volunteer some time to help you out . Old school or new , jury rigged or factory, i can just about sort anything out.
_________________ Roy My vids on Youtube My vids on Streetfire
|
|
Top |
|
Chewy
|
Post subject: Posted: Sat Jun 18, 2005 6:02 pm |
|
Joined: Wed May 04, 2005 8:16 pm Posts: 202 Location: Killeen, TX - residing in IRQ
|
Cool thanks Roy. give me a call 01718419467.
Im still sort of green when it comes to working on cars but all i can say is im trying and learning a lot.
_________________ Martin-
Missing my 82 maro 350 that i sold!
2007 Harley Nighttrain
Saving for my Vette
|
|
Top |
|
Chewy
|
Post subject: Posted: Sun Jun 19, 2005 9:09 pm |
|
Joined: Wed May 04, 2005 8:16 pm Posts: 202 Location: Killeen, TX - residing in IRQ
|
i did a compression check today.
Cyl.
1. 130
3. 135
5. not able to check due to stupid sparkplug socket cant fit past the headers.
7. 110
2. 125
4. 130
6. 130
8. 130
_________________ Martin-
Missing my 82 maro 350 that i sold!
2007 Harley Nighttrain
Saving for my Vette
|
|
Top |
|
Roy
|
Post subject: Posted: Sun Jun 19, 2005 10:21 pm |
|
Joined: Sun May 27, 2001 2:52 pm Posts: 5556 Location: Mehlingen,Rhineland Pfalz, Deutschland
|
The readings you got are with in tolerance IAW GM's service manual. The lowest reading should not be less than 70 percent of the highest reading, and no cylinder read less than 100psi. Now this is for factory engines in passenger cars. I tend to use the 85% rule. Which means 110 psi would be the min for cyl number 7.
On cylinder 7, Was the compression low on the first stroke and then built in successive strokes? If so it could be rings( need to check with a couple squirts of oil in the cylinder for verification).
Or was it low on the first stroke and does not build on following strokes and the addition of oil does not help? If so could be a valve.
Sure would like to know what number 5 cyl was doing. That would help in ruling out some stuff.
_________________ Roy My vids on Youtube My vids on Streetfire
|
|
Top |
|
NXZ28
|
Post subject: Posted: Mon Jun 20, 2005 4:51 am |
|
Joined: Wed May 05, 2004 7:13 am Posts: 706 Location: Vilseck
|
You may have a 350 after all. That compression is pretty low for a mid-80s 305. They usually had 59cc combustion chambers. Did you do your compression check with the throttle wide open on the carb? #7 looks weak but that could be from your rocker arms too tight on the heads. Could be a sticking valve or bad rings. Re adjust you rocker arms and see if it raises the compression. I had the same problem on my 350 and I readjusted all the valves and it made a huge difference.
|
|
Top |
|
Chewy
|
Post subject: Posted: Mon Jun 20, 2005 3:01 pm |
|
Joined: Wed May 04, 2005 8:16 pm Posts: 202 Location: Killeen, TX - residing in IRQ
|
The cyls successively went up with each turn of the motor.I turned the motor over 5 times then checked it. I did that 3 times for each cyl. and took the avg number. the numbers were very close each time. I had the throttle wide open when i checked them.
I have to find some sort of tool to be able to get to that sparkplug. I tried using a wrench with the socket but i cant get the socket on.
_________________ Martin-
Missing my 82 maro 350 that i sold!
2007 Harley Nighttrain
Saving for my Vette
|
|
Top |
|
Roy
|
Post subject: Posted: Mon Jun 20, 2005 3:32 pm |
|
Joined: Sun May 27, 2001 2:52 pm Posts: 5556 Location: Mehlingen,Rhineland Pfalz, Deutschland
|
|
Top |
|
Chewy
|
Post subject: Posted: Wed Jun 22, 2005 11:03 pm |
|
Joined: Wed May 04, 2005 8:16 pm Posts: 202 Location: Killeen, TX - residing in IRQ
|
My tool collection is not that extensive yet When u get over here ill stop by
_________________ Martin-
Missing my 82 maro 350 that i sold!
2007 Harley Nighttrain
Saving for my Vette
|
|
Top |
|
NXZ28
|
Post subject: Posted: Thu Jun 23, 2005 5:46 am |
|
Joined: Wed May 05, 2004 7:13 am Posts: 706 Location: Vilseck
|
Take the rubber grommet out of you spark plug socket. It is in there to grip the plug. When you take it out it may give you enough clearance to get it on the plug. Just be careful not to snap the head of the plug off when you start to take it out.
|
|
Top |
|
Who is online |
Users browsing this forum: No registered users and 11 guests |
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
|
| |